Great Midwest Yacht
sail boat
sail boat

MISCELLANEOUS

Compass
 

Use to read the shifts. Non-racers can use for conventional navigation

Mounted compass assembly 

- mount between stanchions just below forward grating

teak, Ritchie SS2000

GF691
$417.00

teak, Ritchie SS1000

GF692
$270.00

teak, Ritchie RU90

GF693
$182.00

mahogany, Ritchie SS2000

GF591
$407.00

mahogany, Ritchie SS1000

GF592
$260.00

mahogany, Ritchie RU90

GF593
$172.00
Compasses 

Ritchie 2000, dial diameter 4 1/2"

GB833
$330.00

Ritchie 1000, dial diameter 3 3/4"

GB832
$198.00

Ritchie RU90, dial diameter 3"

GB830
$110.00
Compass mounts 

- supply your own compass

teak, for Ritchie SS2000

GE691-1
$87.00

teak, for Ritchie RU90, SS1000

GE691
$72.00

mahogany, for Ritchie SS2000

GE591-1
$77.00

mahogany, for Ritchie RU90, SS1000

GE591
$62.00
Hazard course computer  

- translate the compass readings into lift and header information

GB841
$15.00

Fiberglass
 

Bilge stiffener kit 

- includes foam stiffener strips, bedding and covering fiberglass, requires polyester resin.Stiffen the bilges of your soft fg boat

GB820
$160.00
Stern tanks, pair 

- includesbedding and covering fiberglass, requires polyester resin. Requires fitting. Add flotation tanks to yourearly fg hull

GE020
$160.00
Seat tanks, pair 

- includes bedding and covering fiberglass, unmounted inspection ports, chain plates. Will require new cross- thwart. Replace old leaky, swayback seats in older fg hulls.

GE030
$725.00
Seat horn repair kit 

- fixes the deformation of the forward face of seat tank on some fg hulls

GC720
$52.00

Flotation
 

1 to 2 lb styrofoam sticks to provide TCA-required positive flotation in fiberglass hulls

Sticks 

- bundle of 25 pcs. Fills inside of tanks on fg hulls. 3 bundles needed for one boat.

GE845
$49.50
Shaped blocks 

- hot-wire-shaped to fit wood hulls. For durability, will need coating or bagging

full set, includes packing for shipping

GA015
$635.00

full set

GA015-1
$565.00

bow

GE840
$215.00

seat, 4 pc

GE841
$175.50

forward pcs, set of 2

GE844
$108.35

aft pcs, set of 2

GE842
$67.25

stern, 2-piece set. Also fits older fg hulls without stern tanks

GE843
$174.00

Hull attachments
 

The pieces and parts that attach to exterior of the hull

Bailer  - Anderson Elvstrom 'Super max'. Interior plate 3 x 5 1/4", hole through hull 2 1/8 x 4 11/32"
GB020
$149.00
Centerboard gasket 

- two-piece, heavy-duty folded sailcloth

GB825
$34.00
Gudgeon, ea 

- heavy-duty double-loop strap with 4 mounting holes. Fits 3/8" pintles

RL490
$13.25
Keel strip 

- 1/2" wide aluminum half round

full set

GE820
$93.50

full set with fasteners

GC820
$69.50

stem - runs down stem and extends 8" aft of stem

GE821
$13.50

stem with fasteners

GE821-1
$14.10

forward - runs from stem piece to 2" fwd of CB trunk

GE822
$22.60

trunk - holds the CB gasket in place, pair

GE823
$38.10

aft - from CB trunk to transom

GE824
$19.50
5200 sealant 

- use to seal keel-strip screws. Silicone does NOT work

GB771
$14.47

Lifting
 

Hoist your boat safely

Lifting bridle assembly 

- 3/8" dacron. With 2 stainless S-hooks for attachment to forward grating and D-shackle for aft attachment. Grating hardware is included, aft hardware is not

GF820
$52.25

bridle only

GF821
$45.40
Lifting hardware 

- for permanent attachment to theboat

forward grating hardware for lifting bridle

GF822
$11.25

aft lifting claw for GMW, late D&M

XE179
$16.25

4 hole eye strap for early D&M. Mounts to trunk angled aft cover

RL314B
$2.65

MIscellaneous
 

Inspection port 

- 4", includes fasteners

GC855
$9.00
Closed-end aluminum pop rivets 

use to install inspection ports, attachment of boom end castings

GB722
$0.30
Aluminum washer 

use inside tank as pop-rivet backer when installing inspection ports

GB723
$0.05
Quick-release pin 

- 3/16", solid hardened-stainless pin with ball detent at one end. Caution - the hollow, center-push quick pins will break under shroud loads

medium lenght, attaches shroud to chain plate on seat

GB005
$4.25

short length, attaches shroud to shroud extender or Staymaster

GB013
$3.95
Shroud plate bushings  - needed if you're removing shroud plates for varnishing or replacing rails, pair
GB016
$3.75
Replacement pad 

for spinnaker guy hook, pair

GB310
$3.75

Spinnaker pole
 

Complete pole 

- 1 1/4" aluminum tubing, stainless steel and bronze end fittings, and eyestrap for topping lift attachment

GF130
$200.00

pole only with one end plugged

XF131
$52.00

pole end with fasteners, ea

RF677F
$58.75
Spinnaker pole-end repair parts 

- pin plunger, spring, ring

RF677-1
$7.75

Trailering
 

Thistle trailer 

- Wesco. Galvanized, low-to-the-ground, 5 support rollers

GF993
$2675.00
Trailer center bunk 

- laminated, pressure-treated and padded. Curved to match contour of hull

GC994
$275.00

wood only

GB994
$185.00
Trailering mast support 

- secures to aft grating

GE830
$30.00
Trailering tie-down strap 

GB980
$17.70

Traveler
 

Traveler track and car 

- includes end stops and fasteners. New boats use H2729 for car. Other choices below

GC330-1
$271.80

traveler track, includes end stops and fasteners

H2720-1
$87.05

end stops for traveler track

H173
$8.35
Traveler car 

- all cars are captive-ball style, none fit the old-style track

with eye strap for mainsheet block and 2 sheaves for traveler control

H2729
$184.75

ti-lite, mainsheet block needed is Harken H2651.

H2733
$150.80

pivoting shackle for mainsheet block. Control tangs for attaching traveler blocks or lines

H2754
$183.05
Traveler car balls 

- use to rebuild older-style Harken (loose ball) traveler car.

H177
$12.85
Traveler profile template 

- reduce the height of your transom by removing the wood over the tiller hole. Traveler track will bend to this curve during installation

GG300
$5.00